NDNLPv2¶

NDNLPv2 is a link protocol for Named Data Networking.

Goals¶

NDNLPv2 provides the following features:

• fragmentation and reassembly: fragment a network layer packet to fit in link MTU
• failure detection: rapidly detect link failure and recovery
• reliability: reduce packet loss
• integrity: prevent packet injection
• forwarding instruction: NACK, nexthop choice, cache control, etc
• packet information: for management and monitoring

NDNLPv2 is designed to be a unified protocol that can be used on all kinds of links, including but not limited to: UNIX sockets, Ethernet unicast/multicast, UDP unicast/multicast, TCP connections, WebSockets, etc.

NDNLPv2 protocol operates as a link adaptation layer; it is above link layer and below network layer.
Please, do not call this "layer 2.5": there is no such notion in RFC protocols.

Different links need different features, or different designs of a feature.
NDNLPv2 ensures all features are optional and can be turned on or off per-link.
NDNLPv2 also allows different designs of a feature to be adopted per-link.

NDNLPv2 deprecates and replaces: original NDNLP (aka NDNLPv1), NDNLPv1 multicast extension, NDNLPv1-TLV, NDNLP-BFD, NFD LocalControlHeader.

NDNLP Packet Format¶

NDNLPv2 packet adopts a Type-Length-Value (TLV) structure similar to NDN Packet Format.

LpPacket ::= LP-PACKET-TYPE TLV-LENGTH
               LpHeaderField*
               Fragment?

Outermost packet transmitted on a NDNLPv2 link is LpPacket.
In addition, a host MUST also accept bare network packets (Interest and Data) on a NDNLPv2 link, which SHOULD be interpreted as an LpPacket with the bare network packet as its LpFragment. However, such packets could be dropped later in processing if the link configured to require a certain NDNLPv2 feature but a field is missing.

LpHeaderField is a repeatable optional structure in LpHeader.
NDNLPv2 features MAY add new header fields by extending the definition of LpHeaderField.
Unless otherwise specified, the same field shall appear at most once.
Unless otherwise specified, fields MUST appear in the order of increasing TLV-TYPE codes.

If an incoming LpPacket contains an unknown LpHeaderField, the following rules apply:

1. if the unknown field is in range [800:959], and the two least significant bits are 00, the receive SHOULD ignore the field, and continue processing the packet;
2. otherwise, the receiver MUST drop the packet, but SHOULD NOT consider the link has an error.

Note: if a field is recognized but the relevant feature is disabled, it's not an "unknown field".

Initially, the Sequence header field is defined:

LpHeaderField ::= .. | Sequence

Sequence ::= SEQUENCE-TYPE TLV-LENGTH
               fixed-width unsigned integer

Sequence contains a sequence number that is useful in multiple features.
This field is REQUIRED if any enabled feature is using sequence numbers, otherwise it's OPTIONAL.
Bit width of the sequence is determined on a per-link basis; 8-octet is recommended for today's links.
A host MUST generate consecutive sequence numbers for outgoing packets on the same face.

Fragment ::= FRAGMENT-TYPE TLV-LENGTH
               byte+

Fragment contains a fragment of one or more network layer packets.
The fragmentation and reassembly feature defines how Fragment field is constructed and interpreted.
When fragmentation and reassembly feature is disabled, the Fragment field contains a whole network layer packet.
Fragment is OPTIONAL; LpPacket without Fragment is an IDLE packet.

Indexed Fragmentation¶

Indexed fragmentation provides fragmentation and reassembly feature on datagram links that does not guarantee in-order delivery.

This feature defines two header fields:

LpHeaderField ::= .. | FragIndex | FragCount

FragIndex ::= FRAG-INDEX-TYPE TLV-LENGTH
                nonNegativeInteger

FragCount ::= FRAG-COUNT-TYPE TLV-LENGTH
                nonNegativeInteger

Sender slices a network layer packet into one or more fragments.
The size of each fragment MUST be small enough so that the LpPacket carrying every fragment is below link MTU.
It is RECOMMENDED that all except the last fragments have the same size.

FragCount field indicates the number of fragments belonging to the same network layer packet.
It MUST be the same in all fragments belonging to the same network layer packet.

FragIndex field indicates the zero-based index of the current packet.
It MUST be assigned consecutively for fragments belonging to the same network layer packet, starting from zero.
The feature is named "indexed fragmentation" because every fragment is given an index in this field.

Sequence field is REQUIRED when this feature is enabled.
Fragments belonging to the same network layer packet MUST be assigned consecutive sequence numbers, in the same order with FragIndex.

For example, a 5000-octet network layer packet may be sliced as illustrated:

+-------------+-------------+    +-------------+-------------+
| LpPacket    | Fragment    |    | LpPacket    | Fragment    |
| seq=8801    |             |    | seq=8802    |             |
| FragIndex=0 | [0:1400]    |    | FragIndex=1 | [1400:2800] |
| FragCount=4 |             |    | FragCount=4 |             |
+-------------+-------------+    +-------------+-------------+

+-------------+-------------+    +-------------+-------------+
| LpPacket    | Fragment    |    | LpPacket    | Fragment    |
| seq=8803    |             |    | seq=8804    |             |
| FragIndex=2 | [2800:4200] |    | FragIndex=3 | [4200:5000] |
| FragCount=4 |             |    | FragCount=4 |             |
+-------------+-------------+    +-------------+-------------+

Receiver stores fragments in a PartialMessageStore data structure, which is a collection of PartialMessages, indexed by MessageIdentifier=Sequence-FragIndex.
Since both Sequence and FragIndex are assigned consecutively, MessageIdentifier would be the sequence number of the first fragment of a network layer packet.
After collecting all fragments belonging to a network layer packet, the receiver joins them together, and delivers the complete network layer packet to upper layer.

The receiver SHOULD maintain a reassembly timer in each PartialMessage, which is reset each time a new fragment is received.
If this timer expires, the PartialMessage is dropped.
Default duration for this timer is 500ms.

If this feature is enabled but FragIndex is missing, it is implied as zero.
If this feature is enabled but FragCount is missing, it is implied as one.
If this feature is disabled but either header field is received, the packet MUST be dropped.

Unless otherwise specified, header fields from other features shall only appear on the first fragment.
If a field appear on a non-first fragment, it MUST be ignored.

Network NACK¶

A network NACK is a forwarding instruction from upstream to downstream that indicates the upstream is unable to satisfy an Interest.

This feature defines a header field:

LpHeaderField ::= .. | Nack

Nack ::= NACK-TYPE TLV-LENGTH
           NackReason?

NackReason ::= NACK-REASON-TYPE TLV-LENGTH
                 nonNegativeInteger

Nack header field indicates an Interest is a NACK, and is not a normal Interest.
The receiver MUST NOT process the packet as an Interest.

NackReason element MAY be included to indicate why the NACK is transmitted.

The following NackReason values are defined:

Code	Reason	Description
0	None	(reserved)
50	Congestion	there is a congestion in the link between upstream and downstream, or on the best-known path between upstream and content source
100	Duplicate	the upstream has detected a duplicate Nonce in the Interest sent by the downstream
150	NoRoute	the upstream has no path to reach a content source due to routing problem or link failure

A receiver MUST be prepared to process a NACK without a reason.

If NackReason element contains an unrecognized reason, the receiver MUST treat this NACK as a NACK without reason, and MUST NOT drop the packet.

Example of NACK of an Interest for /example with NACK reason "Duplicate":

+--------------------------+---------------+
| LpPacket                 | Interest      |
|                          | Name=/example |
| +-Nack-----------------+ | Nonce=35      |
| | NackReason=Duplicate | |               |
| +----------------------+ |               |
+--------------------------+---------------+

It's RECOMMENDED to enable this feature on every link.

If this feature is disabled but Nack is received, the packet MUST be dropped.

Nack header field is permitted only on an LpPacket carrying an Interest.

When Nack appears on an LpPacket carrying a network layer packet other than an Interest, the packet MUST be dropped.

Consumer Controlled Forwarding¶

Consumer controlled forwarding allows a local consumer application to explicitly specify the nexthop face to forward an Interest.

This feature defines a header field:

LpHeaderField ::= .. | NextHopFaceId

NextHopFaceId ::= NEXT-HOP-FACE-ID-TYPE TLV-LENGTH
                    nonNegativeInteger

NextHopFaceId indicates the nexthop FaceId to which an Interest should be forwarded.
A local consumer application MAY add this field to an LpPacket carrying an Interest.
The local forwarder SHOULD follow this instruction and forward the Interest to the specified nexthop, after ContentStore lookup does not find a match.

This feature is designed to be used on local faces only.
It SHOULD NOT be enabled on non-local faces.
If this feature is enabled but NextHopFaceId refers to a non-existent face, the Interest SHOULD be processed as if there is no available route.
If this feature is disabled but NextHopFaceId is received, the packet SHOULD be dropped, or this field MUST be ignored.

NextHopFaceId header field is permitted only on an LpPacket carrying an Interest, from an application to the forwarder.
When NextHopFaceId appears on an LpPacket carrying a network layer packet other than an Interest, the packet MUST be dropped.
When NextHopFaceId is received by an application from a forwarder, this field MUST be ignored.

Local Cache Policy¶

Local cache policy feature allows a local producer application to instruct ContentStore on whether and how to cache a Data packet.

This feature defines a header field:

LpHeaderField ::= .. | CachePolicy

CachePolicy ::= CACHE-POLICY-TYPE TLV-LENGTH
                  CachePolicyType

CachePolicyType ::= CACHE-POLICY-TYPE-TYPE TLV-LENGTH
                      nonNegativeInteger

CachePolicy header field gives a suggestion to the ContentStore.
The ContentStore MAY follow this suggestion.

CachePolicyType element MUST be included to indicate the suggestion.
The following CachePolicyType values are defined:

Code	Policy	Description
0	None	(reserved)
1	NoCache	ContentStore SHOULD NOT admit the Data packet

If CachePolicyType field contains an unknown policy code, the forwarder SHOULD drop the packet.

The design places the policy code in the CachePolicyType element nested under CachePolicy, instead of having the code appear directly in CachePolicy header field, because in the future other policies that require additional arguments can be defined, and those arguments can appear as elements after CachePolicyType.

Example for a Data packet with "NoCache" policy:

+-----------------------------+---------------+
| LpPacket                    | Data          |
|                             | Name=/example |
| +-CachePolicy-------------+ | Content=xxxx  |
| | CachePolicyType=NoCache | | Signature=xx  |
| +-------------------------+ |               |
+-----------------------------+---------------+

This feature is designed to be used on local faces only.
It SHOULD NOT be enabled on non-local faces.
If this feature is disabled but CachePolicy is received, this field MUST be ignored.

CachePolicy header field is permitted only on an LpPacket carrying a Data packet, from an application to the forwarder.
When CachePolicy header field appears on an LpPacket carrying a network layer packet other than a Data packet, the packet MUST be dropped.
When CachePolicy is received by an application from a forwarder, this field MUST be ignored.

Incoming Face Indication¶

Incoming face indication feature allows the forwarder to inform local applications about the face on which a packet is received.

This feature defines a header field:

LpHeaderField ::= .. | IncomingFaceId

IncomingFaceId ::= INCOMING-FACE-ID-TYPE TLV-LENGTH
                     nonNegativeInteger

IncomingFaceId contains the FaceId from which the network layer packet is received.
When this feature is enabled, the forwarder SHOULD attach this field to every network layer packet going to a local application, and indicate the FaceId on which this network layer packet is received by the forwarder.
If a Data packet comes from the ContentStore, IncomingFaceId SHOULD contain a special FaceId that represents the ContentStore, rather than the FaceId on which this Data packet was originally received.
Even if this feature is enabled, the application MUST be prepared to receive a packet without IncomingFaceId field.

This feature is designed to be used on local faces only.
It SHOULD NOT be enabled on non-local faces.

IncomingFaceId header field is permitted only on an LpPacket from the forwarder to an application.
When IncomingFaceId is received by the forwarder from an application, this field MUST be ignored.

Congestion Marks¶

A host can signal the current congestion state to other hosts using the CongestionMark field. A value of 0 indicates no congestion; a value greater than 0 indicates some level of congestion. The exact meaning of the bits in this field is left up to the congestion control strategy in use.

This features defines a header field:

LpHeaderField ::= .. | CongestionMark

CongestionMark ::= CONGESTION-MARK-TYPE TLV-LENGTH
                     nonNegativeInteger

TLV-TYPE Code Assignments¶

type	code (decimal)	code (hexadecimal)
LpPacket	100	0x64
Fragment	80	0x50
Sequence	81	0x51
FragIndex	82	0x52
FragCount	83	0x53
HopCount (ndnSIM)	84	0x54
Nack	800	0x0320
NackReason	801	0x0321
NextHopFaceId	816	0x0330
IncomingFaceId	817	0x0331
CachePolicy	820	0x0334
CachePolicyType	821	0x0335
CongestionMark	832	0x0340

Reserved Blocks¶

Two blocks of TLV-TYPE codes have been reserved by link protocols:

• [80:100], 1-octet encoding
• [800:1000], 3-octet encoding

TLV-TYPE codes for LpHeaderField SHOULD be assigned according to the following rules:

1. if the field can be safely ignored by a receiver that doesn't understand the field, pick an unused code in the range [800:959] whose two least significant bits are 00.
2. if the field would occur frequently, pick an unused code in the range [81:99].
3. otherwise, pick an unused code in the range [800:959] whose two least significant bits are 01.

Note: code assignment for a TLV-TYPE nested within a LpHeaderField is not restricted by the above rules.