Project

General

Profile

Watched Prefix Insertion Protocol » History » Version 4

Weiqi Shi, 07/24/2014 01:54 AM

1 1 Weiqi Shi
Watched Prefix Insertion Protocol
2
=================================
3
Watched Prefix is a new protocol for repo insertion. By using this protocol, repo keep sending interests to request the data with same prefix. When a data packet is received, repo will update selectors (exclude selector in most cases) to exclude the received data and request new one. Repo will stop watching the prefix until a command interest in tell it to stop, the total amount of sent interests reaches a specific number or time out.
4
5
## Basic operations
6
7
### Keep requesting and inserting data with same prefix
8
9
Command verb: **watch**
10
11
The name semantics follows the format of the repo command. The <command verb> is defined as ``watch``.
12
For example, for ``<repo prefix>`` as ``/ucla/cs/repo``, the following is an example:
13
14
    /ucla/cs/repo/watch/<RepoCommandParameter>/<timestamp>/<random-value>/<SignatureInfo>/<SignatureValue>
15
16
### Watch status check
17
18
Command verb: **watch check**
19
20
During the watched prefix progress, requester could send watch status check command to check the status of the progress. This status check command is also signed interest. The semantics of watch status check command is shown as follows:
21
22
<command verb> equals to ``watchCheck``. For example:
23
24
    /ucla/cs/repo/watchCheck/<RepoCommandParameter>/<timestamp>/<random-value>/<SignatureInfo>/<SignatureValue>
25
26
## Formats
27
28
### RepoCommandParameter
29
30
The following components are used in watch-prefix command
31
32
* ``Name``
33
* ``Interest timeout``
34
* ``Max number of Interest``
35
* ``Watching timeout``
36
* ``Status``
37
* ``Selectors``
38
* ``ProcessId``
39
40
Name is the prefix that will be watched.
41
42
Interest timeout is the maximum latency between interest sent and data received. If the time duration is larger than interest timeout, the same interest will be resent. If data is received within the Interest timeout, the selectors of the interest will be updated and sent to request new data.
43
44
Max number of Interest is the maximum of total interests that can be sent. The process will stop if the total number of interests reaches this limit.
45
46
Watching timeout is the time duration of this process. Repo will keep watching the prefix until it times out.
47
48
Status is used to show whether repo is watching a prefix or not. 
49
50
ProcessId shows the id number of this command interest, a random number generated by repo.
51
52
Selectors are used to exclude the received data and request new data.
53
54
For watchCheck command interest, only ProcessId is needed.
55
56
### RepoCommandResponse
57
58
This watch status data object could be the response data object of both watch command and watchCheck command. It will follow the format of repo command response.
59
60
Response has three part: ProcessId, indicates an ID of process;  InsertNumber, indicates how many data packets under the watched prefix has been inserted into repo; 
61 2 Weiqi Shi
StatusCode, indicates the status of the process.
62
63
StatusCode Definition:
64
65
``StatusCode`` | Description
66
-------------- | ----------------------------------------------
67
``100``        | The command is OK. Start to watch the prefix
68
``101``        | Watched Prefix Insertion is stop.
69
``300``        | This watched prefix Insertion is in progress
70
``401``        | This watch command or watchCheck command is invalidated
71
``402``        | BlockId present. BlockId is not supported in this protocol
72
``403``        | Malformed Command
73
``404``        | No such this process is in progress
74 3 Weiqi Shi
75
## Protocol Process
76
77
1. Start to validate the command. If it is validated, go to Step 3, otherwise go to Step 2.
78
79
2. Send a negative response indicating validation failure, and abort these steps, process ends (StatusCode: 401).
80
81
3. Check parameters. If it cannot be extracted from interest, send a negative response(StatusCode: 403) and stop process.
82
83
4. If it has BlockId, send a negative response(StatusCode: 402) and stop process.
84
85
5. Use parameter of the command interest to construct interest. Set the Rightmost Child Selector.
86
87
6. Send the interest and start timer. The number of sent interest plus 1(the initial value is 0).
88
89
7. If received a data, go to Step 8, if times out, go to Step 17.
90
91
8. If data is validated, go to Step 9, otherwise, go to Step 15.
92
93
9. Check whether the watched prefix insertion is still running. If it does not, process ends.
94
95
10. If the process times out(exceed watch timeout) or if total number of sent interest reaches limit, go to Step 11, otherwise go to Step 12.
96
97
11. Clear all the variables(the number of sent interest, watch timeout, interest lifetime), abort these steps, process ends.
98
99
12. Store the data into repo.
100
101
13. Update selectors, exclude from min to the received one and use the updated selectors construct new interest. 
102
103
14. Send new interest and the number of sent interest plus 1, and then go to Step 7.
104
105
15. Repeat Step 9 to 11 and skip Step 12.
106
107
16. Update selectors, only exclude the received data(since other data whose name is smaller may be satisfied), then go to Step 14.
108
109
17. Repeat Step 9 to 11 and skip Step 12.
110
111
18. Send the interest again and the number of sent interest plus 1, and then go to Step 7.
112 4 Weiqi Shi
113
For watchCheck command:
114
115
1. Start to validate the check command. If it is validated, go to Step 3, otherwise, go to Step 2.
116
117
2. Send a negative response indicating validation failure, and abort these steps, process ends (StatusCode: 401).
118
119
3. Check parameter. If it cannot extracted from interest or if it does not have processId, send a negative reply(StatusCode: 403).
120
121
4. Check whether the processId is existed. If it does, go to Step 5, otherwise, send a negative reply(StatusCode: 404).
122
123
5. Use the processId to find the response and send the response back.